Легенда:
новое сообщение
закрытая нитка
новое сообщение
в закрытой нитке
старое сообщение
|
- Напоминаю, что масса вопросов по функционированию форума снимается после прочтения его описания.
- Новичкам также крайне полезно ознакомиться с данным документом.
Господа, будьте снисходительны, не бросайтесь сразу штрафовать за, как вам кажется, глупые вопросы - beginners на то и beginners.
ещё подробности... 05.04.03 01:06 Число просмотров: 1571
Автор: fly4life <Александр Кузнецов> Статус: Elderman Отредактировано 05.04.03 01:30 Количество правок: 1
|
> Что, если насильно прижать сетевуху на 10MBit? Утилита > называется rset8139.exe, забрать можно с > Setup/diagnostic program (DOS program) > ftp://152.104.125.40/cn/nic/rtl8139abcd8130810xseries/rset8 > 139-503.zip > размер 38kb. > а потом уже настраивать в линуксе?
Т.е., насколько я понял, ты предлагаешь перепрошить сетявку? Если да, то это не подходит, т.к. 100 мбитная сет мне тоже нужна - на работе.
> Там же на > http://www.realtek.com.tw/downloads/downloads1-3.aspx?serie > s=16&Software=True есть драйвера от Realtek-а под Linux. > > Нашёл тут ещё один how-to - > http://www.tldp.org/HOWTO/Ethernet-HOWTO-4.html#ss4.31 > "RealTek 8129/8139 > Status: Semi-Supported, Driver Name: rtl8139, 8139too > Another PCI single chip ethernet solution from RealTek. A > driver for cards based upon this chip was included in the > v2.0.34 release of linux. You currently have to answer `Y' > when asked if you want experimental drivers for v2.2 > kernels to get access to this driver. > Donald says that cards based on this chip are around the > same price (or even cheaper in places - 13 bucks!) as a PCI > NE2000 clone card, and while the 8139 design is not the > best 10/100 board, it is better than a PCI NE2000 clone > card. > The 2.4.x kernels have another driver called 8139too which > was based on rtl8139 but tries to adress some of the more > common problems people were reporting, so you may wish to > try that if using a 2.4 kernel."
Пасиб, посмотрю...
> Может стОит попробовать тот самый rtl8139 вместо 8139too?
А это мысль.... Может дело и вправду в модуле 8139too..
Я посмотрел настройки сетевухи утилиткой ethtool и вот что она мне выдала:
[root@Nails root]# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: Not reported
Advertised auto-negotiation: No
Speed: 10Mb/s
Duplex: Half
Port: MII
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Supports Wake-on: pumbg
Wake-on: d
Current message level: 0xffffffff (-1)
Link detected: no
Вроде все настройки стоят как мне надо, но сеть всё равно не пашет =((. Причём смущает надпись " Link detected: no"! Как это не линкуется?? На хабе лампочка горит...
В то время как modinfo выдало вот что:
[root@Nails root]# modinfo -p 8139too
multicast_filter_limit int, description "8139too maximum number of filtered multicast addresses"
max_interrupt_work int, description "8139too maximum events handled per interrupt"
media int array (min = 1, max = 8), description "8139too: Bits 4+9: force full duplex, bit 5: 100Mbps"
full_duplex int array (min = 1, max = 8), description "8139too: Force full duplex for board(s) (1)"
debug int, description "8139too bitmapped message enable number"
Т.е. в модуле прописан full duplex на 100 мбит!
Брррр... Теперь я точно запутался! Там 10, тут 100... @#$ проссышь!
Попробую модуль rtl8139, если он у меня скомпилится и захочет работать с ядром 2.4. Немного сомневаюсь я ;)
|
|
|