информационная безопасность
без паники и всерьез
 подробно о проектеRambler's Top100
Страшный баг в WindowsПортрет посетителяSpanning Tree Protocol: недокументированное применение
BugTraq.Ru
Русский BugTraq
 Анализ криптографических сетевых... 
 Модель надежности двухузлового... 
 Специальные марковские модели надежности... 
 Три миллиона электронных замков... 
 Doom на газонокосилках 
 Умер Никлаус Вирт 
главная обзор RSN блог библиотека закон бред форум dnet о проекте
bugtraq.ru / форум / networking
Имя Пароль
ФОРУМ
все доски
FAQ
IRC
новые сообщения
site updates
guestbook
beginners
sysadmin
programming
operating systems
theory
web building
software
hardware
networking
law
hacking
gadgets
job
dnet
humor
miscellaneous
scrap
регистрация





Легенда:
  новое сообщение
  закрытая нитка
  новое сообщение
  в закрытой нитке
  старое сообщение
  • Напоминаю, что масса вопросов по функционированию форума снимается после прочтения его описания.
  • Новичкам также крайне полезно ознакомиться с данным документом.
В IRIX была такая командочка rtquery. Внутри цитирую man rtquery 30.05.01 17:25  Число просмотров: 1066
Автор: SOLDIER Статус: Незарегистрированный пользователь
<"чистая" ссылка>
RTQUERY(1) RTQUERY(1)

NAME
rtquery - query routing daemons for their routing tables

SYNOPSIS
rtquery [-np1] [-w timeout] [-r addr] host ...

DESCRIPTION
Rtquery is used to query a network routing daemon, routed(1M) or
gated(1M), for its routing table by sending a request or poll command.
The routing information in any routing response packets returned is
displayed numerically and symbolically.

Rtquery by default uses the request command. When the -p option is
specified, rtquery uses the poll command, an undocumented extension to
the RIP specification supported by gated(1M). When querying gated(1M),
the poll command is preferred over the Request command because the
response is not subject to Split Horizon and/or Poisoned Reverse, and
because some versions of gated do not answer the Request command. Routed
does not answer the Poll command, but recognizes Requests coming from
does not answer the Poll command, but recognizes Requests coming from
rtquery and so answers completely.

Rtquery is also used to turn tracing on or off in routed.

OPTIONS
-n Normally network and host numbers are displayed both symbolically
and numerically. The -n option displays only the numeric network
and host numbers.

-p Uses the Poll command to request full routing information from
gated(1M). This is an undocumented extension of the RIP protocol
supported only by gated(1M).

-1 query using RIP version 1 instead of RIP version 2.

-w timeout
changes the delay for an answer from each host. By default, each
host is given 15 seconds to respond.

-r addr
ask about the route to destination addr.
-t op
change tracing, where op is one of the following. Requests from
processes not running with UID 0 or on distant networks are
generally ignored by the daemon except for a message in the system
log.

on=tracefile
turn tracing on into the specified file. That file must
usually have been specified when the daemon was started or be
the same as a fixed name, often /etc/routed.trace.

---------------------------------

Вывод! Покупай себе SGI workstation. ;)
<networking> Поиск 






Rambler's Top100
Рейтинг@Mail.ru


  Copyright © 2001-2024 Dmitry Leonov   Page build time: 0 s   Design: Vadim Derkach