#################################################################
# PPP  Sample Configuration File
# Originally written by Toshiharu OHNO
# Simplified 5/14/1999 by wself@cdrom.com
#
# See /usr/share/examples/ppp/ for some examples
#
# $FreeBSD: src/etc/ppp/ppp.conf,v 1.2.2.5 2001/07/13 10:55:23 brian Exp $
#################################################################

default:
 set log Phase Chat LCP IPCP CCP tun command
 ident user-ppp VERSION (built COMPILATIONDATE)

 # Ensure that "device" references the correct serial port
 # for your modem. (cuaa0 = COM1, cuaa1 = COM2)
 #
 set device /dev/cuaa0

 set speed 115200
 set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
           \"\" AT OK-AT-OK ATE1Q0 OK \\dATDT\\T TIMEOUT 40 CONNECT"
 set timeout 180			# 3 minute idle timer (the default)
 enable dns				# request DNS info (for resolv.conf)

papchap:
 #
 # edit the next three lines and replace the items in caps with
 # the values which have been assigned by your ISP.
 #

 set phone PHONE_NUM
 set authname USERNAME
 set authkey PASSWORD

 set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
 add default HISADDR			# Add a (sticky) default route

#########################################################################=
    
    # PPP Link Up File ('/etc/ppp/ppp.linkup')
    #
    #  This file is checked after PPP establishes a network connection.
    # 
    #  This file is searched in the following order.
    #
    #  1) First, the IP address assigned to us is searched and
    #     the associated command(s) are executed.
    #
    #  2) If the IP Address is not found, then the label name specified at
    
    #     PPP startup time is searched and the associated command(s) 
    #     are executed.
    #
    #  3) If neither of the above are found then commands under the label
    #     'MYADDR:' are executed.
    #
    #########################################################################=
    
    #
    # This section is used for the "demand" configuration in
    #   /etc/ppp/ppp.conf:
    demand:
     delete ALL
     add 0 0 HISADDR
    #
    # All other configurations in /etc/ppp/ppp.conf use this:
    #
    MYADDR:
     add 0 0 HISADDR
    ########################################################################
    # End of /etc/ppp/ppp.linkup

> ###########################################################
> ######
> # PPP  Sample Configuration File
> # Originally written by Toshiharu OHNO
> # Simplified 5/14/1999 by wself@cdrom.com
> #
> # See /usr/share/examples/ppp/ for some examples
> #
> # $FreeBSD: src/etc/ppp/ppp.conf,v 1.2.2.5 2001/07/13
> 10:55:23 brian Exp $
> ###########################################################
> ######
> 
> default:
>  set log Phase Chat LCP IPCP CCP tun command
>  ident user-ppp VERSION (built COMPILATIONDATE)
> 
>  # Ensure that "device" references the correct serial port
>  # for your modem. (cuaa0 = COM1, cuaa1 = COM2)
>  #
>  set device /dev/cuaa0
> 
>  set speed 115200

попробуй уменьшить скорость до 57600

>  set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
> 	   \"\" AT OK-AT-OK ATE1Q0 OK \\dATDТ\\T TIMEOUT 40

> timer (the default)
>  enable dns				# request DNS info
> (for resolv.conf)
> 

> 

>  set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
>  add default HISADDR			# Add a (sticky)
> default route

> 

pap
	     Default: Disabled and Accepted.  PAP stands for Password Authen­
	     tication Protocol.  Only one of PAP and CHAP (above) may be nego­
	     tiated.  With PAP, the ID and Password are sent repeatedly to the
	     peer until authentication is acknowledged or the connection is
	     terminated.  This is a rather poor security mechanism.  It is
	     only performed when the connection is first established.  If you
	     want to have your peer authenticate itself, you must ``enable
	     pap''.  in /etc/ppp/ppp.conf, and have an entry in
	     /etc/ppp/ppp.secret for the peer (although see the ``passwdauth''
	     and ``set radius'' options below).

	     When using PAP as the client, you need only specify ``AuthName''
	     and ``AuthKey'' in /etc/ppp/ppp.conf.  PAP is accepted by
	     default.
passwdauth
	     Default: Disabled.  Enabling this option will tell the PAP
	     authentication code to use the password database (see passwd(5))
	     to authenticate the caller if they cannot be found in the
	     /etc/ppp/ppp.secret file.	/etc/ppp/ppp.secret is always checked
	     first.  If you wish to use passwords from passwd(5), but also to
	     specify an IP number or label for a given client, use ``*'' as
	     the client password in /etc/ppp/ppp.secret